Introduction to the daily operation of the pattern machine and teach you how to improve the embroidery quality of the pattern design
Introduction to the daily operation of the pattern machine: 1. The height between the intermediate presser and the sewing material should be adjusted to O. 5mm. 2. The clearance between the lower shaft gear and the swing gear should be adjusted to O.1mm. 3. How to adjust the clearance between the thread hook and the needle? Suitable use range: Ethylene ,Ripener,fruits,Hestening Rooting, Growth Weifang Xinchang Chemical Co.,Ltd , http://www.xinchangchem.com
Introduction to the daily operation of the pattern machine and teach you how to improve the embroidery quality of the pattern design
Introduction to the daily operation of the pattern machine:
1. The height between the intermediate presser and the sewing material should be adjusted to O. 5mm.
2. The clearance between the lower shaft gear and the swing gear should be adjusted to 0.1 mm.
3. How to adjust the gap between the wire hook and the needle?
Answer: 1 Turn the handwheel so that the distance between the needle and the needle plate is 1 9.5mm.
2. Loosen the thread sweeper drive crank screw (2).
3. After pressing the wire sweeping drive crank (3) of the thread wiper, adjust the thread sweeping shaft (4) so ​​that the thread sweeping hook
The distance from the needle is 1Omm.
4. Tighten the wire drive crank screw (2).
5. Loosen the fixing screw (5) of the wire hook so that the gap between the lower end of the wire hook and the needle tip is 1mm.
Tighten the screws again.
How to set the 4.xY origin?
Answer: 1. Move the feeding bracket so that the center of the upper feeding plate in the x direction is consistent with the machine hole.
2. Loosen the two screws on the x-axis sensor bracket and move the sensor bracket to make the x-ray
The piece is centered on the x-axis sensor and the screw is tightened.
3. Remove the right cover.
4. Move the feeding bracket so that the center of the upper feeding plate in the Y direction is consistent with the needle hole.
5. Loosen the Y-direction PV chip screw and turn the Y-direction photo-electric film so that the Y-direction photo-electric film is located on the Y-axis.
Center the sensor and tighten the screws.
How is the position of the five-line sensor adjusted?
A: When there is no wire on the thread take-up spring, loosen the screw on the wire detection board, put the spring and the test board
After touching, tighten the screws.
Teach you how to improve the embroidery quality of the pattern design:
Those who have used the embroidery machine usually have the effect of embroidering the embroidered machine and the original version.
In the case of big differences, such problems cannot be solved quickly.
To this end, we specifically explore how to improve the embroidery quality of the embroidery version. First you
Consider the fabric and shape that you need to embroider. If the embroidery is deformed, you should consider using shrinkage.
Compensate to make the shape embroidered correctly, or the fabric needs to use stitching stitches to achieve stability.
Use automatic lower seam, shrink compensation, short stitch step, fine adjustment value and smart corner to achieve stitching
Smooth, even placement, and eliminate gaps in the design of the pattern, specifically explained below
.
1. Use automatic lower seam
Embroidize the lower stitch before filling the stitch to stabilize the fabric or prevent the thread from getting caught in the fabric.
The best type of lower seam depends on the size of the fabric, the shape and the type of stitching used. More
Large areas and elastic fabrics such as knits and embossed fabrics have smaller areas and such as twill
The hard fabric of cloth or leather needs to use the lower seam.
2. Use shrinkage compensation
The fabric is pulled inward (contracted toward the embroidery needle) by the thread that passes through the fabric.
This has the potential to wrinkle the fabric and create a gap in the fabric. Automatic shrinkage compensation is
The needle is “excessively embroidered†on both sides of the fabric to fill the contour of the needle shape, so it automatically collects
The shrinkage compensation can counteract such undesirable results of wrinkling and gap creation.
Experienced pattern makers can also overlap objects as they are being plated (ie, when stroked)
Use a manual method to compensate for shrinkage.
3. Minimize stitching in curves or corners
You can also use the trim value or short stitch to reduce the stitching. Sharp outer edge
Causes the stitch to bulge along the inner edge. When the shape is embroidered, the embroidery thread is broken. Stitch
The longer the problem, the more serious the problem.
Use the trimming value for the shape of the curve so that the stitch density along both the outer and inner edges is
uniform. Short stitch steps are used at the curved object to reduce the stitch density inside the curved object.
4. Reduce stitching at the sharp corners
The sharp corners in the shape cause the stitches and stitches to bulge, forming a hard part on the fabric
And may also damage the fabric or break the embroidery needle. Use smart corners to help you lose
Enter the method A and the input method C object to control the sharp corners. There are two types: beveled seam corners and
Cap-shaped corner.
5. Adjust stitch density
Use the stitch processor to adjust the stitch density when scaling or not. When using different fabrics
Or embroidering the thread, or in order to reduce the production cost, this will reduce the stitching of the embroidery version.
Http://news.chinawj.com.cn Submission:
Banana, Mango, Tomato, Citrus, Melons......
Product components and features:
This product function components in Ethylene gas, in line with the national standard
GB9830-88 "fruit and vegetable cold storage after ripening" requirements, safety, no residue.