Decoration main material usage calculation method

>>>Links: Designers must have 20 basic knowledge, culture and skills

1, floor tile usage: (Note generally different room type loss rate is different about 1-5%)
Amount per hundred meters = 100/<(length of block + width of slot) × (width of block + width of slot)> × (1 + loss rate)
For example, the size of the retro floor tile is 0.5×0.5M, the width of the joint is 0.002M, the loss rate is 1%, and the required number of blocks for 100 square meters is:
100 square meters =100/<(0.5+0.002)×(0.5+0.002)×(1+0.01) approximately equal to the total price of 401 tiles = floor tiles × floor tiles

3, ceiling usage:
Roof plate usage=(length-shield length)×(width-shield width)
For example, the amount of PVC plastic ceiling can be calculated from the net size area. The unit price of PVC plastic sheet is 50.81 yuan per square meter, the shield length and width are 0.24M, the length of the canopy is 3M, and the width is 4.5M. The dosage is as follows:
Roofing plate usage = (3-0.24) x (4.5-0.24) approximately equal to 11.76 per square meter

3, package door dosage:
Package door material usage = door outer frame length × door frame width, for example (as shown in the figure) with composite wood package door, door outer frame length 2.7M, width 1.5M, then its material usage is as follows:
Package door material dosage=2.7×1.5=4.05 square meters

4, wallpaper usage:
Wallpaper Usage = (High - Shielded Length) × (Width - Shielded Width) × Number of Walls - Door Area - Window Area (For example) Wall Area is calculated as net size, shield is 24CM, wall height is 2.5M, width is 5M, The door area is 2.8 square meters and the window area is 3.6 square meters. The dosage is as follows:
The usage of wallpaper =<(2.5-0.24)×(5-0.24)>×4-2.8-3.6 is equal to approximately 36.6 square meters. It is a calculation of the amount of material used. After multiplying the amount of decoration materials used for each part by the respective unit price, Adding up, you get the total material cost of the renovation project.

5, floor dosage: (solid wood)
Longitudinal usage = room length / length of floor tile Lateral usage = room width / width of the floor tile If you encounter endless, use the carry method, do not round, but less than half of the longitudinal calculation half, more than half a block.
Total floor price = total usage × unit price floor loss = floor area - floor area floor loss rate = floor loss / housing area Note: General floor wear rate is not more than 5%

6. After determining the color variety of the wall-mounting material usage wall-mounting material, the size of the material can be reasonably calculated based on the size of the living room. Considering the possible loss during construction, it can be purchased with about 5% more than the actual amount. There are two ways to calculate wall materials:
1. Calculated by the formula, the area of ​​the room is multiplied by 2.5, and the product is the number of materials used for the wall. Such as 20 square meters of room materials used for 20 × 2.5 = 50m. There is also a more precise formula:
S=(L/M + 1)(H + h) + C/M
Including: S - length of required wall material (m)
L--Total length of the wall after deducting windows, doors, etc. (m)
M - the width of the wall material (m), plus 1 as a splicing pattern margin;
H--the height of the required wall material (m)
h - distance between two identical patterns on a wall material (m)
C--the area of ​​the wall required for up and down windows, doors, etc. (square meters)
2. On-site measurement, this method is more accurate, first understand the width of the wall material to be selected, measure the perimeter of the room wall (excluding doors, windows, etc.) according to the width, there are several wall materials in the perimeter Width, that is, a few stickers. Then measure the height of the wall that should be affixed. Multiply this by the number of walls, which is the length (in meters) of wall material required for the wall outside the door and window. Finally, the length of material required for the wall under the window, irregular corners, etc. is measured by this method, and it is added to the calculated length, which is the total length. This method is more suitable for fine-grained patterns, without special alignment of the wall material when splicing.

7. The method for estimating the amount of paint introduced a simple calculation method:
The room area (square meters) divided by four, the height of the wall to be painted (in decimeters) divided by four, the sum of the two is the number of kilograms of paint required. For example, a room with an area of ​​20 square meters and a wall height of 28 decimeters would be (20÷4)+(28÷4)=12, ie 12 kg of paint can be painted on the wall twice.

Decoration start preparation del floor nature floor room window wallpaper paint decoration design floor tile brick

Bolts

HCH Hardware is a bolt manufacturer and provides all kindsof fasteners since 2008. Our main products includestandard bolts, nuts, Screws, washers, Pins and OEM parts. We have integrated resources from more than 50 top level fastener factories in Jiaxing, Haiyan, Ningbo,Dainan, Qintongareas, and have established long term relationships with them.We arenow serving for over 60 customers in South and North America.We can provide you with one stop services to meet you different needs, which can save your purchasing cost and optimize your efficiency. HCH Hardware was certified by ISO9001-2015 on 02/25/2021.We especially emphasize on products quality,HCH Hardware have necessary conditions for quality control with applicable processes and experienced experts. Appropriate production processes and quality control
actions can meet clients` highexpectation on quality and services.

Metal Bolt,Locking Bolt,Furniture Bolts,Steel Bolt

Taizhou Hongchuang Hardware Co., Ltd. , https://www.taizhouhongchuang.com