Water saving

1. The hot water tap should not be opened to the maximum: when the hot water is turned on until the hot water flows out, the boiler has a delay of about 6 seconds. At this time, the pipeline between the boiler and the faucet is cold water, so even during this time. It is also cool water that drives the faucet to the maximum flow. If you drive to the maximum, there will be a lot of cold water to be wasted. Therefore, when using hot water, you should first open a small water flow, wait for the boiler to start until the ignition delay, and then adjust the water flow according to your needs, so you can save a lot of water, and the water heating time is short. Especially the large-sized apartment with the bathroom far from the boiler is particularly obvious.

2. Store the cold water flowing out before the hot water flows out; if the small water flow does not start, it may be that the boiler is dirty or the hot water starts to be insensitive, or the water flow is too small (not required by the controller) The starting water flow) can be found by professional maintenance personnel to solve the problem or slightly increase the water flow.

3. Minimize the number of faucets in the process of bathing: Because every time the hot faucet is switched once, the boiler will start once, and there will be a delay of about 6 seconds. During this time, a lot of cold water is wasted. . Moreover, when the boiler is in hot water, it burns with a large fire before it reaches the set temperature, which also increases the gas consumption.

Solar terms

1. The wall-hung boiler itself is the key to the solar energy. A gas-saving wall-hung boiler can save you a lot of follow-up costs. First of all, the national energy efficiency mark is a must. Of course, the higher the energy efficiency, the better, but now the state has the highest level. Secondly, the original imported more exhaust gas. Because the mix ratio of gas in each region is different, and the economic conditions of residents are different. Therefore, many foreign brands have undergone localization after entering China. Volvo in Germany has improved the German design into a national situation suitable for China. The small fire platoon commonly used in European fireplaces has been changed to a high fire pipe temperature. The temperature of the pipe greatly reduces the energy consumption.

2, close or reduce the radiator valve in the unoccupied room: If your housing area is large, the room is more, and the population is relatively small, then the radiator valve of the room that is not live or low frequency is completely It can be turned off or turned down, which is equivalent to reducing the heating area, not only saving energy, but also increasing the heating temperature in the space of normal use, reducing gas consumption.

3. When no one is working in the daytime, it is not advisable to turn off the wall-hung boiler and adjust the temperature gear to the lowest level: many office workers are used to shutting down the boiler when they are no one at home, and then put the boiler in high-grade for rapid heating after work. The practice is very unscientific. Because this means that everything starts from the beginning, because the temperature difference between the room temperature and the set temperature of the boiler is large, the boiler needs time to run on fire, so that not only does it not save energy, but it will waste more gas and increase the freezing time of the household, and there is a boiler or radiator. The danger of being frozen.

4. If you have been on a long-term business trip or have not yet lived, drain the water from the boiler and radiator: It is recommended that you ask the professional to drain the water from the boiler and radiator so that you can not only use the gas, but also the boiler. Or the radiator is frozen.

New Design Grow Led Light

The spectrum of LED plant lights can be adjusted according to the needs of different plants to provide the most suitable lighting conditions for plant growth. The newly designed plant lights also focus on appearance and user experience. They typically have a simple, stylish exterior design that harmonizes with the interior environment and is easy to install and operate. Some plant lights also have adjustable poles and lamp heads designed to better illuminate the plants.

The newly designed plant grow light is a special lighting device designed to provide indoor plants with the required light conditions to promote their growth and healthy development. This plant grow light uses advanced LED technology and has the following features:

1. Spectrum adjustment: grow lights can provide the full spectrum of light, including red, blue, yellow and other different wavelengths of light. This can adjust the color and intensity of the light according to the needs of different plants to promote their photosynthesis and growth.

2. High efficiency and energy saving: LED technology has the characteristics of high efficiency and energy saving, compared with traditional fluorescent lamps or incandescent lamps, plant lamps can provide more light intensity, while consuming less energy, reducing energy waste.

3. Long life: LED lamps have a long service life, generally up to tens of thousands of hours, more durable and reliable than other lamps.

4. Easy to operate: led grow lightss are usually equipped with an intelligent control system, which can be adjusted and timing switched by mobile phone App or remote control. Users can customize the brightness, color and working time of the light according to the needs of the plant.

5. Beautiful design: The newly designed plant lamp pays attention to the aesthetic appearance, the shell is made of high-quality materials, the appearance is simple and fashionable, and is suitable for various indoor environments.

plants full spectrum led grow light blue and red,light the best led grow light for indoor plants veg,660nm grow light

Shenzhen Pvison Technology Co., Ltd. , https://www.pvisunggrowlight.com