Plywood door production manipulator installation process
Plywood doors are used in many homes, such as bedroom doors, toilet doors, balcony doors, etc. These "doors" can be used as plywood doors, so it can also be called indoor special doors. The use of the plywood door is very extensive, so its installation process must be fine, so as not to affect everyone's life safety. For example, in many homes, splint doors are used, such as bedroom doors, toilet doors, balcony doors, etc. These "doors" can be used as plywood doors, so it can also be called indoor special doors. The use of the plywood door is very extensive, so its installation process must be fine, so as not to affect everyone's life safety. If the splint door is not well installed, there is a possibility of slumping. It is best to check the ply door when it is installed many times. Then let me introduce how to install the plywood door.
The Holding Magnets Roundt are used in the precast concrete production structures to form free spaces in the work-pieces to fix the concrete inserts. Holding Magnets are used in Magnetic Shuttering System. This equipment type has considerably simplified some production task for the concrete structures producers. It easily gets fixed in the magnet formwork system or on the steel table due to its magnetic properties.
SHINE Holding Magnets offers long term reliability and cost effective solutions for the precast industry. Our products are durable and they last for years under all conditions. With our unique combination of rubber and integrated magnets, you can make almost any shape. Once it´s in place, it stays put. No slipping, no sliding.
Plywood door production operation
1. Plywood door production operation procedures and general requirements:
Door and window production operation procedures: batching → cutting → planing → chiseling → opening, cutting → finishing line angle → stacking → assembling;
2. Ingredients and materials for construction
1) Ingredients and cut-offs should pay special attention to careful calculation and matching, and should not be used for large materials and long materials. When using species of masson pine, casuarina, birch, poplar, and insects, the whole component should be treated with anti-corrosion and insect-repellent agents. ;
2) It is necessary to determine the machining allowance reasonably. The processing allowance of width and thickness is 3mm for one plane, and 5mm for both sides. For components with a length of 50cm or less, the machining allowance can be 3-4mm;
3) When the door frame material has a smooth bend, the curvature should not exceed 4mm. The bender is generally not allowed to use;
4) Green skin and inverted sputum can be used if they are perfect on the front and the cut. If the back is more than 1/6 of the thickness of the wood and 1/5 of the length, it is generally not allowed to use.
Plywood door installation process
(1) The interior of the finished plywood door can be installed after the basic decoration is completed.
(2) After the finished door enters the site, it is necessary to carry out careful inspection and set up a special stacking ground to prevent it from being damaged or raining.
(3) The door frame with good safety is protected by an adhesive multi-layer board to prevent collision.
(4) The hardware should be in the correct position and fixed with wood screws. It should not be replaced by iron nails. It should be drilled into 1/3 depth first, then tightened and screwed. It is strictly prohibited to drive all depths.
(5) Before the installation of the plywood door frame, the outside of the frame shall be treated with anti-corrosion treatment. After the door leaf is installed, the flatness and diagonal inspection shall be carried out.
(6) The splint door leaf must be installed firmly, the switch is flexible, the closing is tight, and there is no flapping.
(7) The surface of the plywood door is clean, no shading or hammering; the cutting angle of the wooden door and the seam are tight and flat; the door and window frame and the fan cutting edge are straight and the planing surface is flat; the groove and the hole edge on the plywood door are neat and burr-free.
Be sure to pay attention when installing the plywood door. The plywood door belongs to a very light skeleton door. It has thin-walled doors made of different materials on both sides, including plywood and fiberboard. These two materials are used for plywood door selection. The point is that if the material of the plywood door is less than one of them, it is not a qualified splint door. Before installation, be sure to pay attention to the installation, do not be wet, otherwise it will be prone to degumming. Tips, do not install the splint door on the outer door.
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Holding Magnets Round,Neodymium Pot Magnets,Pot Magnet With External Thread,External Thread Neodymium Pot Magnet
Ningbo Shine Magnetic Technology Co., Ltd. , https://www.shutteringmagnetic.com