To successfully enter the decoration process, we must first fully understand our house. When we inspect the house, we can fully communicate with designers and decoration workers, carefully check and accept, and prepare for the next renovation.

Doors and windows must be closed

When closing the house, check whether the door is open and closed smoothly, whether the installation is firm, whether the switch is flexible, whether the surface is clean, smooth, scratch-free, bump, whether the door plug is inserted too little or too long or too tight. It is also necessary to check the sealing performance of the door, whether the door-to-door clearance is too large, especially one side of the door lock, and whether the four sides of the door are in close contact with the door frame; if there is a special sound when the door is opened and closed.

When checking the window, you should carefully check the gap between the window edge and the concrete interface; the seams on the frame wall must be dense and have no gap; whether the switch window is too tight, whether the opening and closing is smooth, and whether the window glass is in good condition, whether or not it has quality problems, Whether the screen window returns smoothly or not. Also look carefully at the water stains below the windowsill. This can tell if the windows are leaking. The glass must be carefully observed for scratches and breakage, and the surface is smooth.

Observe the cracks in the ceiling, wall, and ground

Look carefully for cracks on the top. No cracks are the best. Cracks look like cracks. In general, cracks parallel to the room beams do not substantially interfere with use. If the crack is at an angle of 45 degrees to the corner of the wall, or even perpendicular to the beam, then it is a sign that the subsidence of the house is serious and the house has serious structural quality problems.

Look at the top if there are pits, such pits professionally known as "lime burst point", will have an adverse effect on indoor re-decoration. Check the roof there are no water stains, cracks, waterlogging if there is any suspicion of leakage.

Observe the wall in the direction of light to see if there are any signs of cracking and repair, and it is best to understand the reason for smearing. If the flatness of the wall is better, there is no need for leveling or patching, which can also save the decoration time.

Ask for a circuit diagram to facilitate renovation

Whether it is a circuit or a waterway, the circuit problem should be an extremely important link.

It is advisable to ask for the circuit wiring diagrams from the escorting personnel. This is the circuit design and construction drawing left by the construction party for the owner after the completion of the housing or renovation, so as to provide reference for future maintenance. In this way, at the beginning of the renovation, changes can be easily made when carrying out hydropower reforms.

Years ago

Decrease the amount of work for years to stay

If you must complete the renovation before the year before, it is necessary to do a detailed renovation plan, but also to master some of the decoration techniques, such as the winter can be opened for heating decoration, less woodworking, etc., to reduce the amount of work.

Heated decoration

The most demanding time for winter decoration is cement, mortar and leveling. The drying problem may take 20 to 30 days to dry out under normal conditions. Since it is winter, you can open up the heating to decorate it. The progress of wall and floor leveling work has been reduced to about 15 days. In general, it takes a long time to finish the work on the wall and the ground. It must wait until it is completely dry before proceeding to the next step.

In order to accelerate drying, we must also pay attention to quality, and must strictly follow the engineering requirements of the project. For example, the putty on the wall must be fully dried and scraped a second time in the first pass. Otherwise, the quality of the wall will be cracked after the completion of the work. For example, the cement mortar on the ground floor tile does not reach the early strength and it will go up. With a foot, there is also a hollow problem.

Doing less woodworking

In the winter, the degree of dryness of the wood is the best, and the moisture content is much lower than in other seasons. The finished products made of such wood are not easy to crack and deform. In addition, the indoor heating is sufficient. Before the paint is applied, the potential problems of the wood are quickly exposed. Timely repair, so that the painted wood or furniture can maintain its original appearance for a long time.

However, the winter carpentry should be remembered thoroughly and dry, although heating will accelerate drying. However, due to the large wind and sand in winter, paint and paint are likely to adhere to dust when they are not dry. Care should be taken to select a windless weather for painting so as not to affect the surface texture. Ventilation afterwards is also very important, so less carpentry can also accelerate the construction period to a certain extent.

Decoration start preparation entrance decoration decoration company window heating paint switch glass glass brick glass door glass furniture craft glass

Welding Nut

Welding nut is a kind of nut suitable for welding outside the nut. It is generally made of weldable material and is relatively thick and suitable for welding. Welding is equivalent to turning two separated parts into a whole, melting the metal at high temperature, mixing it together and then cooling it. Alloy will be added in the middle, and molecular force will play a role in the inside, and the strength is generally greater than that of the parent body. The experiment of welding parameters depends on the fusion size of the weld, and the welding parameters are adjusted according to the fusion size until the defects are eliminated. Of course, the quality of welding is related to the pre-welding treatment, such as dust removal and oil stain.

Welding Nut,Round Weld Nuts,Weld Nuts Lowe'S,Weld Nuts Fastenal

Jiangsu Jiajie Special Screw Co., Ltd , https://www.jiajiebolts.com