ã€Asia pump network】 I-1B thick pump features and installation methods I-1B-type thick pump Features: 1. Can deliver high concentrations of high viscosity <10000PaS and suspended particles containing slurry. 2. Delivery of liquid flow stability, no over-current, pulsation and mixing, shear slurry phenomenon. 3. Discharge pressure has nothing to do with the speed, low flow can also maintain high discharge pressure. 4. Flow and speed is proportional to the speed through the variable speed mechanism or motor control. 5. Self-priming ability, without bottling valve can be aspirated liquid. 6. Thick pump reversible, the liquid flow direction by the pump to change the direction of rotation for the pipeline to be washed in any case. 7. Smooth operation, vibration, noise. 8. Simple structure, disassembly and maintenance easy. Thick pump widely used in chemical, pharmaceutical, brewing, paper making, food and other units. I-1B-type thick pump installation instructions: According to the general plan of the pump and the instructions provided by the installation size casting foundation and determine the location of anchor bolts, under normal circumstances should not change the direction of imports. The basic surface should be leveled by the level meter, and the foundation should be installed on the basis of the solidified cement. Concentricity of motor shaft and pump shaft. Two axis offset does not exceed ± 0.2 mm. If the axis does not coincide, it will produce vibration bearing heat, or even damage the pump. Pump suction and discharge pipes should have their own and support, generally do not allow the pump body to withstand the weight of the pipeline, the pump can be inverted when the tank can not be installed at the end of the valve, but the suction pipe should be installed on the control valve and the filter device to Anti-debris inhalation pump. When the pump is installed above the liquid level, the bottom valve should be installed at the suction pipe end, and the area of ​​the throat of the bottom valve should be larger than 50% of the trifoliate trifoliate cross-section of the suction pipe. Pumps must be thoroughly cleaned prior to the installation of debris within the pipeline, such as: welding slag, metal shavings, etc., in order to avoid pump start inch inhalation caused an accident. I-1B-type thick pump instructions for use: Start: 1. The necessary wrenches and tools. 2. Inspect the machine base, lubricate the bearing and oil chamber, 3. Check if the hollow shaft and shaft seal degree are proper, and the packing gland can not press packing too tightly. Or pipe clamp rotation shaft. Note that there is no noise in the pump body touch the sound and stuck stuck. If there is should be cleared before driving 5. Fluid filled the pump chamber. Do not rub the operation. To avoid damage to the village sets 6. All the liquid valve gate 7. Open the motor. Shutdown: 1. Close the suction pipe valve. 2. Close the drain valve. 3. Stop the motor [When the pump is stopped for long periods of time, 0] .Please fill the pump chamber with water or steam. Operation: 1. Regularly check the temperature rise of the pump and motor bearings, the maximum temperature should not exceed 75 ℃. 2. Timely replenishment of lubricants to ensure good bearing lubrication. 3. During operation, if abnormal noise or excessive vibration is found, it should be shut down immediately for checking. 4. When the flow significantly reduced, indicating that the rubber casing has been worn. (Editor: Xiaoxia QQ:) Recommended reading: 2017 exhibition information
Shandong Fiberglass Group Corp. is a state owned enterprise with registered capital RMB400million, covering an area of 800,000sqm. It has 3 subsidiaries: Tianju Energy Saving Material Corp, Glasstex Fiberglass Material Corp and Yishui Thermo Electricty Plant. Currently we can provide 7 categories products with 300 more kind products in ECR fiber, Ecering@Tex Modified Fiber,c-glass fiber, Wallcoveing, Insect Screen, PCB Tissue and Mesh.We are certified enterprise group with IS09001, ISO18001, ISO14001, Germannischer Lloyd(GL),UL and CQM certificates. Now we ranked China 4th largest Fiberglass producer. In 2020, we would become world Top 7 largest fiberglass producer with roving annual capacity 450,000tons, and fabrics capacity 230,000,000sqm. And some of our products capacity would become China Top 1, like C-CR Speicial glass fiber, ECR High properties glass fiber, Ecering@-Tex modified glass fiber and wallcovering.